Home Security Store Knowledgebase

View Articles by Category

There are no sub categories
Add an article to this category

Category » PowerMax Plusrss button

(Page 1 of 2)      Prev | 1 | 2 | Next

There were 21 articles found in this category:

  1. questionPowerMax Plus - How to I program the PowerMax Plus to call out to private phone numbers?
    To program the system to call out - Press NEXT until you see INSTALLERS MODE, then press SHOW/OK Now press 9999 Press NEXT until you see DEFINE PANEL on display, then press SHOW/OK Press NEXT until you see 05 ABORT TIME, press Show/OK (If you see 00s, just press Show/OK) (If you see anything ...
  2. questionHow can I wire and program an l.e.d. light,to indicate an armed or disarmed system status outside my home?
    †To begin, you will need an l.e.d. rated for use between 9 and 12 volts dc, a†1000 ohm resistor and 22 or 24 gauge 2 conductor wire,†available at most†local electronic hardware†stores† The positive l.e.d. wire will twist to one end of the 1000 ohm resistor...the other end of the resistor will co ...
  3. questionHow do I program the GSM module as a back up communicator?
    These steps are for programming the gsm module for use as a back up†communicator†to a monitored system. These instructions assume all††private phone numbers or†central station receiver phone numbers and account info has been set up already. † † † Begin by†pressing NEXT until INSTALLERS MODE is ...
  4. questionHow do I enroll the MCM140 into the Powermax+ system?
    To enroll the MCM140 keypad, Press the NEXT key until you see INSTALLERS MODE on display, then press OK Press 9999 Now Press NEXT until you see "ENROLLING" on display, press OK Now press NEXT until you see ENROLL 1 WAY KP, press OK Now press NEXT to see " 1 way KP 1", press the OK button, you s ...
  5. questionPowermax+ - How do I program so the central station receives a weekly test signal?
    To set up the Powermax+ to send a test signal to the monitoring company, once per week, follow the steps below. Enter the Installers mode by pressing NEXT until Installers mode is displayed, then press OK Now enter the installers code of 9999 (enter yours if this was changed) Press NEXT until y ...
  6. questionPowermax+ - How do I program for an X10 siren?
    † Press NEXT until you see Installers Mode, then press OK Enter 9999 when prompted Press NEXT until you see DEFINE PANEL, press OK Now press NEXT until you see 05 ABORT TIME, press OK Now press NEXT until you see 00s, press OK twice, if it is already set to 00s, press OK once Now press AWAY then ...
  7. questionVisonic PowerMax Plus - How can I change the User Code?
    To change User Code 01: -Press the NEXT key until "USER SETTINGS" is displayed, then press SHOW/OK -The system will ask for the code. -Press 1111 (or current master code) -Press the NEXT key until " SET USER CODES" is displayed, then press SHOW/OK -You should see CODE 1 -Press SHOW/OK -Enter you ...
  8. questionVisonic PowerMax Plus - How does the IM-SS15 wire to the Powermax Plus?
    To connect the IM-SS15 siren to the Powermax+ Connect the red wire from the siren to the 12v+ terminal on the Powermax+ Connect the white siren to the EXT terminal on the Powermax+ The Yellow wire from the IM-SS15 will not be used.
  9. questionVisonic PowerMax Plus - Can I use the keyfob to arm the system to "instant" mode?
    YES, The * key on the keyfob can be set up to allow instant arming. Press NEXT until you see Installers Mode, then press the Show/OK button Enter 9999 Press NEXT until you see DEFINE PANEL then press SHOW/OK Press NEXT until you see 17 AUX BUTTON press SHOW/OK Press NEXT until "INSTANT" appears ...
  10. questionVisonic PowerMax Plus - Why canít I change my Userís Code?
    The most common reason for not being able to change the User Code 1 is that the intended code was already programmed as the Installers code.To correct the situation, enter the Installers mode and change the Installers Code back to 9999 then go to the User Settings section, sub section Set Access ...
  11. questionVisonic PowerMax Plus - How do I wire a hardwired contact to the MCT302?
    A hardwired contact can be connected to the 2 screw terminals located inside the transmitter case. The cover has a wiring knockout that will allow the wires to enter the transmitters case and still be able to close the transmitters cover and secure it with the screw.There are smal dip style swit ...
  12. questionVisonic PowerMax Plus - What does Tamper Alarm mean?
    The term tamper alarm is an indication that a transmitters cover was opened or the main CPU was removed from it's mounting bracket and unless the message is followed by the announcement "Tamper Open" can be cleared by arming and disarming the system.This message will be accompanied by either a z ...
  13. questionVisonic PowerMax Plus - What does the reference CPU mean?
    The term CPU references the main console. (control panel unit)
  14. questionVisonic PowerMax Plus - What size wire can be used for wiring the transformer?
    The wire can be between an 18 to 22 gauge 2 conductor wire.
  15. questionVisonic PowerMax Plus - Why is the Trouble light on?
    Pressing the Show/Ok button will cause the system to describe any troubles with the system.Press the Show/Ok button, making notes as you go, until there are no more announcements heard. Check the User's manual once you have a description of the problem.
  16. questionVisonic PowerMax Plus - The wireless motion detector is not working all the time.
    The wireless motion detector has a built in battery saver circuit which limits the signaling to once every 2 1/2 minutes. Follow the provided literature to place the motion detector in the "walk test" mode. In this mode the motion detector will transmit each time it is tripped for use when insta ...
  17. questionVisonic PowerMax Plus - How do I wire the transformer?
    A length of wire may have been provided and will be connected between the 2 screw terminals on the transformer and the blue screw terminal block located on the back of the Powermax+ CPU labeled "9 VAC". The blue screw terminal block can be removed for easier access by lifting straight up on it ...
  18. questionVisonic PowerMax Plus - What does Tamper Open mean?
    The message "tamper open" will be associated with a zone name or zone number, or even For example, if when pressing the Show/Ok button the message states "CPU Tamper Open", this means that the Powermax+ main console is either not mounted on the back bracket or the main consoles battery compartme ...
  19. questionVisonic PowerMax Plus - How do I clear the Memory message from the display?
    Arming and disarming the system will clear any memory messages on display.
  20. questionVisonic Powermax Plus - How do I set up an X10 Powerhorn?
    Note: When using an X10 siren with the Powermax+ system, you will be programming the system so the X10 siren is assigned as House Code A Device number 1. In order for the X10 siren to work properly, turn the dials on the X10 siren to B 1 The correct programming steps are listed below press NEXT ...
(Page 1 of 2)      Prev | 1 | 2 | Next