Security System | Technical Support | Home Security Store - Recent Entries http://knowledgebase.homesecuritystore.com en-us http://knowledgebase.homesecuritystore.com ActiveKB NX justin@homesecuritystore.com Sat, 21 Nov 2009 05:37:01 PST 20 How do I delete and enroll and wireless transmitter, I have an NX8 control and NX548E wireless receiver? http://knowledgebase.homesecuritystore.com/questions/101/ To delete a transmitter zone 9 used as an example) 1. Enter * 8 at the keypad. (On LED touchpads, the five function lights start flashing.) 2. Enter the program code (factory default is 9 7 1 ... Freddie Amaral Wed, 06 May 2009 18:57:51 GMT How can I wire and program an l.e.d. light,to indicate an armed or disarmed system status outside my home? http://knowledgebase.homesecuritystore.com/questions/100/ To begin, you will need an l.e.d. rated for use between 9 and 12 volts dc, a 1000 ohm resistor and 22 or 24 gauge 2 conductor wire, available at most local electronic hardware stores The positi ... Freddie Amaral Fri, 01 May 2009 18:57:34 GMT How do I enroll the NX470 keyfob into my NX-6-FP-7-RF system? http://knowledgebase.homesecuritystore.com/questions/99/ To enroll the NX470 as zone 9, for example: Press * 8 9713 192 # 910 # (exit key) (exit key) wait about 30 seconds and then continue Press * 8 9713 192 # 594 # 0 * 400 # 9 * (hold the top 2 b ... Freddie Amaral Fri, 01 May 2009 18:47:23 GMT How do I program the GSM module as a back up communicator? http://knowledgebase.homesecuritystore.com/questions/98/ These steps are for programming the gsm module for use as a back up communicator to a monitored system. These instructions assume all private phone numbers or central station receiver phone nu ... Freddie Amaral Thu, 30 Apr 2009 18:54:02 GMT How does the BV300DP wire to the DSC PC1832 ? http://knowledgebase.homesecuritystore.com/questions/97/ The wiring consists of 4 colors, I'll use red,black,yellow and green for example Connect the BV300DP 12v+ to the 1832s AUX+ terminal using the red wire Connect the black wire from the BV300DPs G ... Freddie Amaral Tue, 31 Mar 2009 15:14:40 GMT How do I enroll the MCM140 into the Powermax+ system? http://knowledgebase.homesecuritystore.com/questions/96/ To enroll the MCM140 keypad, Press the NEXT key until you see INSTALLERS MODE on display, then press OK Press 9999 Now Press NEXT until you see "ENROLLING" on display, press OK Now press NEXT ... Freddie Amaral Tue, 31 Mar 2009 14:47:52 GMT I can not access Installers Mode and the User Code works , what can I do to access Installers Mode? http://knowledgebase.homesecuritystore.com/questions/95/ Since you know your user code, you should be able to access the USER SETTINGS section by pressing the NEXT button.Then press the Show/OK button. The system will ask for the code, enter it and y ... Freddie Amaral Tue, 31 Mar 2009 14:35:40 GMT PC1616/PC1832/PC1864 - Example of changing a zone type. http://knowledgebase.homesecuritystore.com/questions/94/ To change the zone types, you enter programming with * 8 5555 The section related to zone types for zones 1-16 is section 001, so you'd press 001 The very next 2 digit entry, fills in the zone ... Freddie Amaral Thu, 29 Jan 2009 16:08:40 GMT DVRP90NV - How do I back up to my USB flashdrive? http://knowledgebase.homesecuritystore.com/questions/92/ You must stop the recording, insert USB flash drive on back of your DVR. Use the play button to get to the event list. Select the event you choose to back up by pressing the record button. It ... Steve Overholt Wed, 28 Jan 2009 15:01:42 GMT DVRP90NV - How do I set the date and time? http://knowledgebase.homesecuritystore.com/questions/93/ To set the date and time you will need to make sure recording is stopped.Press the menu button.Use the arrows up or down until you get to system setupPress the enter buttonUse the arrows up or ... Matt Apperson Wed, 28 Jan 2009 15:01:29 GMT