Advanced Search

Search Results for "programming"

1. Locked out? How to gain access to installer mode programming after you are locke... [Article]
   Step 1: You will need to remove the power supply and battery. Wait 10 seconds and then reapply the battery and power supply. Step 2: Wait for the ready screen to show up on the tou
2. AD2000, AD2001, & AVD-2005 - Why does not my dialer activate when I apply a ... [Article]
   The 1K-ohm resistor (provided) needs to be installed across the alarm output terminals of the alarm panel or across the input terminals of the dialer (such as; 1 and C). Program the specified input fo...
3. AD2000, AD2001, & AVD-2005 - Why doesn’t my dialer activate when I remove th... [Article]
   The 1K-ohm resistor (provided) needs to be installed across the alarm output terminals of the alarm panel or across the input terminals of the dialer (such as 1 and C). Program the specified input for...
4. AD2000, AD2001, & AVD-2005 - How can I install my dialer to work with a rela... [Article]
   Attach the input leads of the dialer to the relay as follows: For Normally Closed activation; Input from dialer (such as; 1) to the Normally Closed (N.C.) terminal of the relay and common (C) from the...
5. Alexor - How do I program my Alexor to call out? [Article]
   Press * 8 5555 301 XXXXXX * 55555 * # (X = phone number to be called) 302 XXXXXX * 55555 * # (X = phone number to be called) 310 1 2 3 4 5 6 320 31 32 33
6. Powermax Plus DIY Installation - X10 Devices (pt.1) [Article]
   Freddie shows you how to set-up and program X10 Devices to your Po
7. Powermax Plus DIY Installation - X10 Devices (pt.2) [Article]
   Freddie shows you how to set-up and program X10 Devices to your P
8. NDIS - THE INTERCOM DOES NOT CONNECT TO ANOTHER INTERCOM AND GREEN LIGHT IS ON L... [Article]
   The intercom is out of range. Place the intercom closer to the other intercoms in the network. With the antenna pointing up. The other intercom in the network has no
9. FGD0400 & FGD0800 - The FGD400 will not answer the telephone when called for... [Article]
   Cause a) Rings Until Answer is incorrectly programmed. b) The FGD400 is connected
10. FGD0400 & FGD0800 - The FGD400 fails to dial out. Why is this and what shou... [Article]
    Cause a) The telephone number may be incorrectly programmed. b) Tone or pulse (th
11. FGD0400 & FGD0800 - The unit says “Error 2.” What should I do? [Article]
    Cause Programming changes were attempted without unlocking the keypad. S
12. FGD0400 & FGD0800 - The unit says “Error 1.” What should I do? [Article]
    Cause An invalid value has been entered or too much time has passed without entering a value.
13. EA200 & EA400 - Does the Blue Low Temp Sensor have a blue tip? [Article]
    No, it has a cylindrical stainless steel tip or black overmold with a blue band at the base. The temperature sensor with the blue tip is legacy sensor part number 1107, which requires diffe
14. EA200 & EA400 - How do I turn a zone off? [Article]
    Set the Zone to Disabled (no) if a Zone is not to be used. If an unconnected Zone is not disabled, nuisance alarms may occur.
15. EA200 & EA400 - How do I unlock the EA400 or EA200 unit for programming? [Article]
    Simultaneously press and release the ALARM SILENCE and ENTER keys. The (Unlocked) icon appears.
16. LW2702 - Why can I not use my own pictures in Screen Saver mode? [Article]
    The system is not a digital picture frame. It is a surveillance system that can simulate a picture frame. The images used in Screen Saver mode are pre-loaded onto the system firmware, not
17. PowerMax Plus - How to I program the PowerMax Plus to call out to private phone ... [Article]
    To program the system to call out - Press NEXT until you see INSTALLERS MODE, then press SHOW/OK
18. OPTEX Wireless 1000 - Do you have a repeater for the Wireless 1000? [Article]
    Yes.  It's the TR10U.  It provides an additional 1000 feet clear line of sight.
19. OPTEX Wireless 1000 - Is there a way to change the frequency on the RC10U? [Article]
    No. It cannot be changed.
20. VA6000S - How do I use the dry contacts on the bottom of the Receiver/Speaker to... [Article]
    There are four "C" relays (aka terminal outputs) on the bottom of the VA-6000S Base Unit. When a Sensor is triggered, you have the option of activating an external device hooked up to one of thes